GeoffDickson
New
I want to design and construct a ‘bullet- proof’ home hitting net that is Flightscope capable. I need your help to get it right.
Model 1: No ceiling
6m distance from tee to net
4m high back net
The Vertical Launch Angle to hit over net (VLA(max)) = 33.7*
PGA Tour PW = 24.2*
At 6m distance, 24.2* hits impact net at height of 2.7m. This provides safety margin of 1.3m
Known issues:
1. No protection for uncommon but almost inevitable skied shots…and one might be one too many. This could be ‘resolved’ by not hitting teed shots, but that takes a bit of the fun out of it.
Questions:
Is the above math correct (http://www.visualtrig.com/)?
Is the above logic correct?
Is the 1.3m safety margin sufficient?
What club could I hit and keep it within the 4m high back net?
Model 2: Ceiling
Given there is always the risk of skying a teed shot (i.e driver, 3 wood), I want to explore the feasibility of a ceiling net. Lets assume the same basic structure: 6m distance from tee to net and 4m high back net.
Model 2A: Just cover the entire floor area with a net.
Model 2B: Provide a ‘partial ceiling’. The net would run the entire width of the net, but hang Xm above the ground (i.e. lower than the 4m perimeter netting), start Ym in front of the tee (i.e. not directly overhead the golfer but close enough to catch the skied shots) and finish Zm from the back net (so that anything that passes under the ceiling net hits the back net and anything that would gone over the net, is caught by the ceiling net.
I can’t find any Flightscope recommendations for minimum ceiling height, but Trackman talks about 3m minimum and 3.5m optimal. Presumably this would permit you to hit up to 60* wedge and still get a reading???
I need some help/advice in calculating the best value for X, Y and Z. Then I can figure out the cost benefit of 2A compared to Model 2A.
Any other comments and suggestions also appreciated. Thanks.
Model 1: No ceiling
6m distance from tee to net
4m high back net
The Vertical Launch Angle to hit over net (VLA(max)) = 33.7*
PGA Tour PW = 24.2*
At 6m distance, 24.2* hits impact net at height of 2.7m. This provides safety margin of 1.3m
Known issues:
1. No protection for uncommon but almost inevitable skied shots…and one might be one too many. This could be ‘resolved’ by not hitting teed shots, but that takes a bit of the fun out of it.
Questions:
Is the above math correct (http://www.visualtrig.com/)?
Is the above logic correct?
Is the 1.3m safety margin sufficient?
What club could I hit and keep it within the 4m high back net?
Model 2: Ceiling
Given there is always the risk of skying a teed shot (i.e driver, 3 wood), I want to explore the feasibility of a ceiling net. Lets assume the same basic structure: 6m distance from tee to net and 4m high back net.
Model 2A: Just cover the entire floor area with a net.
Model 2B: Provide a ‘partial ceiling’. The net would run the entire width of the net, but hang Xm above the ground (i.e. lower than the 4m perimeter netting), start Ym in front of the tee (i.e. not directly overhead the golfer but close enough to catch the skied shots) and finish Zm from the back net (so that anything that passes under the ceiling net hits the back net and anything that would gone over the net, is caught by the ceiling net.
I can’t find any Flightscope recommendations for minimum ceiling height, but Trackman talks about 3m minimum and 3.5m optimal. Presumably this would permit you to hit up to 60* wedge and still get a reading???
I need some help/advice in calculating the best value for X, Y and Z. Then I can figure out the cost benefit of 2A compared to Model 2A.
Any other comments and suggestions also appreciated. Thanks.